OnePlus 3 Screen Repair, Teardown and Reassemble

OnePlus 3 Screen Repair, Teardown and Reassemble Guide

Find affordable, high quality OnePlus 3 replacement screens and parts here.

Recommended Tools:

Plastic Triangle Opening Tool
T2 Torx Screwdriver
Nylon Spudger
SIM Card Ejection Tool
Fine Tip Curved Tweezers
Precision Knife Set
2mm Red Adhesive
Multi-Purpose Heat Gun
Professional Phillips Screwdriver
Playing Cards

Step 1

Power down your OnePlus 3 phone.
 
Step 2 (OnePlus 3 Dual Nano-SIM Card Tray)
 
Remove the dual Nano-SIM card tray.
 
Step 3 (OnePlus 3 Rear Case)
 
Remove the following 2 T2 Torx screws from the bottom of the OnePlus 3.
 
Use the plastic triangle opening tool to release the clips and then pop the OnePlus 3 out of its rear metal enclosure. There is no pesky adhesive, making this procedure a snap.

Step 4 (OnePlus 3 Battery)
 
Disconnect the OnePlus 3 battery from the logic board.
 
Remove the following Phillips screw, and then the metal bracket.
 
Detach and remove the interconnect cable.
 
Detach the USB-C port cable from the logic board.
 
Use the exposed clear plastic pull tab to peel the 3000 milliampere-hour (mAh) battery off the adhesive securing it to the OnePlus 3.
 
Step 5 (OnePlus 3 USB-C Port, Loudspeaker, Headphone Jack and Microphone Assembly)
 
Disconnect the 3 cables from the USB-C port assembly.
 
Remove the following 7 Phillips screws.
 
Easily pry up the OnePlus 3 USB-C port, headphone jack, and loudspeaker assembly.
 
Use the spudger to remove the small daughterboard. It includes the 3.5 mm headphone jack, a microphone, and some control hardware and spring contacts.
 
Now separate the OnePlus 3 USB-C port and loudspeaker box.
 
Step 6 (OnePlus 3 Logic Board)
 
Disconnect the signal cable and OnePlus 3 display assembly cable from the logic board.
 
Remove the following 7 Phillips screws.
 
With the cables detached, and screws removed, decouple the OnePlus 3 logic board from the display assembly.
 
Step 7 (OnePlus 3 Front-Facing Camera and Rear-Facing Camera)
 
Peel up the tape, and then detach the 8-megapixel OnePlus 3 front-facing camera.
 
Use the spudger to free the 16-megapixel, auto-HDR OnePlus 3 rear-facing camera from the logic board.
 
Step 8 (OnePlus 3 Earpiece Speaker, Power and Volume Buttons Cable, and Signal Cable)
 
Pop the spring-contact-connected OnePlus 3 earpiece speaker out of the display assembly.
 
With the tweezers, carefully peel up the OnePlus 3 power and volume buttons ribbon cable.
 
Remove the signal cable from the side of the frame.
 
Step 9 (OnePlus 3 Capacitive Home Button and Fingerprint Sensor)
 
Extracting the OnePlus 3 capacitive home button and fingerprint sensor is a breeze. If issues develop with the home button, the absence of solder or adhesive will make it an easy fix.
 
Step 10 (OnePlus 3 Display Assembly)
 
Use the heat gun to warm up the adhesive securing the OnePlus 3 LCD screen and digitizer assembly to the front frame.
 
With the precision knife, carefully create separation and insert a playing card to start slicing through the adhesive.
 
Take your time and apply additional heat as needed. Patiently work around the OnePlus 3 display assembly with picks and playing cards to free it from the frame.
 
Once you have sliced through the adhesive, be mindful of the display’s cable and the cables for the bottom buttons when separating the LCD Assembly from the frame.
 
Step 11 (OnePlus 3 Capacitive Bottom Button Cables)
 
Carefully peel up the cables for the bottom buttons from the front panel.
 
 
* To reassemble your device, follow the steps in reverse order.

 

You can save time by selecting any number of products from this page and then add them all to the cart with just one click.