Asus ZenFone 3 Display Assembly Repair

Asus ZenFone 3 Display Assembly Repair Guide

Find affordable Asus ZenFone 3 repair parts here.

Recommended Tools:

Plastic Triangle Opening Tool
Nylon Spudger
SIM Card Ejection Tool
Fine Tip Curved Tweezers
Precision Knife Set
2mm Red Adhesive
Multi-Purpose Heat Gun
Phillips Screwdriver
Playing Cards

Step 1 

Power down your Asus smartphone.
 
Step 2 (Asus ZenFone 3 SIM card and microSD Card Tray)
 
Eject the SIM card and microSD Card Tray.
 
Step 3 (Asus ZenFone 3 Rear Glass Panel)
 
The ZenFone 3 rear glass panel is glued on solidly and is a tight fit within the narrow bezel. Apply heat to soften the adhesive.
 
With the precision knife create enough space to insert a playing card.
 
Attack the adhesive and carefully dislodge the 2.5D corning gorilla glass rear panel from the phone.
 
Step 4 (Asus ZenFone 3 Exterior Midframe, Fingerprint Sensor, and Loudspeaker)
 
Remove the following 19 Phillips screws.
 
Detach the fingerprint sensor cable and signal cable from the ZenFone 3 motherboard.
 
Use the spudger to pry up the plastic exterior midframe. It includes the ZenFone 3 fingerprint sensor and rear camera lens cover.
 
Extricate the Asus ZenFone 3 loudspeaker module from the bottom of the phone.
 
Step 5 (Asus ZenFone 3 USB-C Port/Daughterboard, Signal Cable, and Vibrator)
 
Detach the ZenFone 3 battery connector from the motherboard.
 
Extract the signal cable from the side of the interior midframe.
 
Peel up the piece of Kaptan tape and disconnect the display cable from the daughterboard.
 
Detach the interconnect cable.
 
Remove the following Phillips screw.
 
Remove the daughterboard from the Asus phone. It includes the Zenfone 3 USB-C port, primary microphone, vibrator, spring contacts, and some control hardware.
 
Step 6 (Asus ZenFone 3 Battery)
 
Locate the two peel-to-remove adhesive tabs at the bottom of the ZenFone 3 battery. Grab the first tab and try to keep the adhesive strip flat and wide.
 
Slowly and gently pull each strip up and away from the Asus smartphone. The strips will stretch to many times the length of the battery- keep pulling until they come out from between the battery and the midframe.
 
And just like that, out pops the 3,000 milliampere-hour (mAh), 3.85-volt Asus ZenFone 3 battery.
 
Step 7 (Asus ZenFone 3 Motherboard)
 
Disconnect the bevy of cables from the Asus ZenFone 3 motherboard.
 
Remove the following 3 Phillips screws.
 
Carefully free the motherboard from the gob of thermal paste securing it to the Asus phone.
 
Step 8 (Asus ZenFone 3 Headphone Jack and Microphone Assembly, Earpiece Speaker, and Rear-Facing Camera)
 
Remove the following Phillips screw.
 
With the tweezers in hand, pry the 3.5mm headphone jack and microphone assembly up and away from the chassis.
 
Tweeze out the spring-contact-connected ZenFone 3 earpiece speaker.
 
Remove the 16-megapixel Asus ZenFone 3 rear-facing camera with the latest Sony IMX298 sensor.
 
Step 9 (Asus ZenFone 3 Display Assembly)
 
Peel the digitizer cable up from the Asus midframe.
 
Begin to free the 5.5-inch ZenFone 3 display assembly by using the heat gun to warm up the adhesive securing it to the interior midframe.
 
With the precision knife create enough space to insert a playing card.
 
Use the playing card to attack the sticky adhesive. Take your time and apply additional heat as needed.
 
Once you have sliced through the adhesive, be mindful of the display’s cables when decoupling the Asus ZenFone 3 screen from the frame.
 
 
* To reassemble your device, follow the steps in reverse order.

 

You can save time by selecting any number of products from this page and then add them all to the cart with just one click.